Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
The writer is making a few great pointers on the subject of How to Install a Bathtub as a whole in this post on the next paragraphs.
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily available, the job can move speedily; if you have to open up a wall to get rid of the old tub and also position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the new one. Ensure you have actually certified on your own for the work and also fit trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is much better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube links.
This post will aid you set up a brand-new bathtub in your shower room if you have already gotten a new bathtub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Planning for the Installation
First of all, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps unit to stop strain on the tub.
Fit the versatile faucet adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted gain access to that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, place the tub in the called for setting. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bath tub till the level checks out degree.
To install taps, fit all-time low of the outermost adaptable faucet connector to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water system and examine all joints and also new pipework for leakages as well as tighten them if required. Load the tub as well as likewise check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub should wait up until the tub has been made use of at least when as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in place in between the faucet as well as the sink. Protect the faucet in position with the producer given backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind needs to be connected to the tap ends initially, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack an inflexible seal, creating the water to permeate the wall in between the bathroom and the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently readily available on the market. It is recommended to fit the ceramic tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that editorial on A Step-by-Step Guide to Installing a Bathtub through an associate on another web blog. Do you know about another individual who is interested in the topic? Be sure promote it. Thanks for your time. Come back soon.
Book Your Installation Report this page